Meny Lukk
  • 90MM SUPER FLEX 26GA SILICONE SENSOR WIRE

  • 125MM SUPER FLEX 26GA SILICONE SENSOR WIRE

    50 kr NOK
  • LRP Hall Sensor Level Converter – 100mm

    Due to not standardized Hall sensor signals there are some non-LRP motors which may not operate properly with the Flow X. This is because the Hall sensors of these motors raise the signals to a higher level than the Flow X can handle properly.

    When connecting such a motor to the Flow X, its start-up sequence may be interrupted and cannot be completed properly, resulting in faulty behavior of the ESC such as:
    – ESC does not respond to throttle input at all
    – Blue LED freezes (solid ON)
    – Pushing SET or MODE button is confirmed with green LED but you cannot enter transmitter setup or Mode programming.
    – No Motor Drive

    To solve this problem the Hall Sensor Level Converter lowers the Hall sensor signals of problematic motors to a level which the Flow X can handle properly.

    Please note that this is the only functionality of the Hall Sensor Level Converter.There is no other advantage or disadvantage, there is no performance increase whatsoever.

    We suggest to proceed as follows:
    1. Use your desired motor with the Flow X with a regular Hall sensor wire. If the motor performs properly, continue to use the regular Hall sensor wire.
    2. Only if your desired motor doesn’t perform properly with the Flow X with a regular Hall sensor wire, use the Hall Sensor Level Converter.

    LRP Flow X = NOSRAM HD – same ESC 🙂

  • LRP Hall Sensor Level Converter – 100mm

    Due to not standardized Hall sensor signals there are some non-LRP motors which may not operate properly with the Flow X. This is because the Hall sensors of these motors raise the signals to a higher level than the Flow X can handle properly.

    When connecting such a motor to the Flow X, its start-up sequence may be interrupted and cannot be completed properly, resulting in faulty behavior of the ESC such as:
    – ESC does not respond to throttle input at all
    – Blue LED freezes (solid ON)
    – Pushing SET or MODE button is confirmed with green LED but you cannot enter transmitter setup or Mode programming.
    – No Motor Drive

    To solve this problem the Hall Sensor Level Converter lowers the Hall sensor signals of problematic motors to a level which the Flow X can handle properly.

    Please note that this is the only functionality of the Hall Sensor Level Converter.There is no other advantage or disadvantage, there is no performance increase whatsoever.

    We suggest to proceed as follows:
    1. Use your desired motor with the Flow X with a regular Hall sensor wire. If the motor performs properly, continue to use the regular Hall sensor wire.
    2. Only if your desired motor doesn’t perform properly with the Flow X with a regular Hall sensor wire, use the Hall Sensor Level Converter.

    LRP Flow X = NOSRAM HD – same ESC 🙂

    125 kr NOK
  • Keep your wiring super neat with this CORE RC flat 90mm sensor wire. Cool black look.

  • Super Flexible Sensor Cable 150mm for Brushless ESC

  • LRP Hall Sensor Level Converter – 100mm

    Due to not standardized Hall sensor signals there are some non-Nosram motors which may not operate properly with the Flow X. This is because the Hall sensors of these motors raise the signals to a higher level than the Flow X can handle properly.

    When connecting such a motor to the Flow X, its start-up sequence may be interrupted and cannot be completed properly, resulting in faulty behavior of the ESC such as:
    – ESC does not respond to throttle input at all
    – Blue LED freezes (solid ON)
    – Pushing SET or MODE button is confirmed with green LED but you cannot enter transmitter setup or Mode programming.
    – No Motor Drive

    To solve this problem the Hall Sensor Level Converter lowers the Hall sensor signals of problematic motors to a level which the Flow X can handle properly.

    Please note that this is the only functionality of the Hall Sensor Level Converter.There is no other advantage or disadvantage, there is no performance increase whatsoever.

    We suggest to proceed as follows:
    1. Use your desired motor with the Flow X with a regular Hall sensor wire. If the motor performs properly, continue to use the regular Hall sensor wire.
    2. Only if your desired motor doesn’t perform properly with the Flow X with a regular Hall sensor wire, use the Hall Sensor Level Converter.

    LRP Flow X = NOSRAM HD – same ESC 🙂

  • 150MM SUPER FLEX 26GA SILICONE SENSOR WIRE

    50 kr NOK
  • 100MM SUPER FLEX 26GA SILICONE SENSOR WIRE

    50 kr NOK
  • Super Flexible Sensor Cable 180mm for Brushless ESC

    50 kr NOK
  • Super Flexible Sensor Cable 225mm for Brushless ESC

  • Super Flexible Sensor Cable 135mm for Brushless ESC

  • Super Flexible Sensor Cable 90mm for Brushless ESC

  • Sensorkabel 135mm

    40 kr NOK
  • Fleksibel sensorkabel 100mm

    50 kr NOK