Meny Lukk
  • 85 kr NOK

    With the increase in surface area contact to a normal washer, these Wing Washers will reduce the amount of wing deflection at higher speeds increasing drivability and stability. They will also reduce the chance of the wing being ripped off during high impact.

    Specification & Content

    • Increases Wing Stability
    • Countersunk Head
    • Aluminium Wing Washers (×2)
    • Stainless Steel Countersunk Screws (×2)
    • Black Nyloc M3 Nuts (×2)
  • 265 kr NOK

    Introducing a brand new product line from PROTOform: the Better Edge System. For every r/c enthusiast that takes pride in finishing off their concours-worthy race body, these products are for you.

    The Better Edge sanding drum is our first product in this line. There has never been a product specifically made for r/c racers to finish off the perfect wheel-well. With the use of your handheld rotary tool, the Better Edge Sanding Drum will smooth out all of the imperfections left from cutting your lexan body with scissors. At 1.5” in diameter, it’s suitable for use on many scales of body: from 1:12 scale on up to 1:8 or even off-road bodies.

    The drum’s red and black anodized aluminum finish and laser-etched PROTOform logos give it a trick look on your pit table. Each pre-assembled kit comes with a replaceable high-grade silicon carbide spiral sanding band, rubber anti-slip o-rings and a mandrel made from durable tool steel to prevent damage from your rotary tool’s chuck.

    Give your r/c race body a better edge!

  • 195 kr NOK

    Compared to the traditional but now obsolete tape paper, aspects and advantages of our Masking Liquid are easily found:

    incredible time savings, the drawing up of liquid is really fast
    possibility to easily reach every point on the surface of the body, even the edges and areas where the lexan has articulated forms
    less usury of the cutting blade of your precision cutter
    greater cutting precision due to the fact that the liquid, once dried, is semi-transparent and facilitates a lot the possibility to follow the lines of your drawing
    no residue when removing the liquid (it may happen, however, if you continue to use an inadequate tape paper that after the removal of adhesive some glue residues remain on the surface of airbrushing; with Liquid Mask this will never happen)
    greater accuracy of airbrushing, with our liquid the color smear are no longer a problem

  • 310 kr NOK

    Compared to the traditional but now obsolete tape paper, aspects and advantages of our Masking Liquid are easily found:

    incredible time savings, the drawing up of liquid is really fast
    possibility to easily reach every point on the surface of the body, even the edges and areas where the lexan has articulated forms
    less usury of the cutting blade of your precision cutter
    greater cutting precision due to the fact that the liquid, once dried, is semi-transparent and facilitates a lot the possibility to follow the lines of your drawing
    no residue when removing the liquid (it may happen, however, if you continue to use an inadequate tape paper that after the removal of adhesive some glue residues remain on the surface of airbrushing; with Liquid Mask this will never happen)
    greater accuracy of airbrushing, with our liquid the color smear are no longer a problem

  • Plassholder
    150 kr NOK

    Our bodyshell stiffeners reduce the chance of a body tuck. They add very little weight (2.7g Mounted) for the strength gained on the rear bumper and wheel arch due to their lightweight effective design. Each type is designed at a different angle to fit the line of most 200mm and 190mm bodyshells, see ‘Selecting Your Bodyshell Stiffener’ below. They are perfect for any racer looking for a lightweight solution to reduce the chance of a body tuck during a run or even worse, the main finals.

    Specifications & Contents

    • Body Stiffener ‘Left’ (0.75g)
    • Body Stiffener ‘Right’ (0.75g)
    • Low Profile Screws x6 (0.2g)
    • Reusable Plastic Packaging

    Selecting Your Bodyshell Stiffener

    Zoo Racing

    Preopard (Type 4) – DBX (Type 3) – Hellcat (Type 4) – Baybee (Type 2)

    Protoform

    Tourismo (Type 4) – LTC 1 (Type 2) – P47 (Type 1)

    Bittydesign

    Extreme

    Twister (Type 3) –

    Montech

    YSOT (Type 4) – 

  • 30 kr NOK

    Bumper & Body Space Setup Sponge Set.
    Brukes til å fylle tomrommet mellom karrosseri og støtfanger.

  • 70 kr NOK

    Ekstra papir til slipekloss for karrosserier

  • 110 kr NOK

    We’ve all been there before. Hours of preparation, countless practice laps, flawless qualifying runs and at last you’ve reached the moment of truth: the finals. In an instant, a simple tap or swipe across the rear bumper from a fellow racer ends your podium hopes. The dreaded body tuck.

    PROTOform has developed Anti-Tuck Body Stiffeners to help remedy this frustrating problem. Made from super-stiff lexan®, the one-piece stiffener fastens inside the rear of your 190mm touring car body with three simple screws & nuts. The pieces are custom formed to fit the curvature of the lower rear fenders for a perfect fit. Not only will this system virtually eliminate body tuck, but the added rigidity will also aid unwanted fluttering or deflection of the rear of the race body at high speeds. Weighing in at only 4.5 grams, changing the weight bias or center of gravity of your car is minimized. Each set comes with two Anti-Tuck Body Stiffeners, mounting hardware and a PROTOform decal sheet.

    Say goodbye to body tuck with PROTOform Anti-Tuck Body Stiffeners.

  • 55 kr NOK

    Vingefester av aluminum

  • 235 kr NOK

    Magnetfeste for lettere å montere karrosseri

  • 75 kr NOK

    Reservepapir for Sanding Drum

  • 100 kr NOK

    Slipekloss for karrosserier